Browse development boards, displays, wireless modules and prototyping hardware. Check each product for specifications and available options.
Показаны результаты 681–700 из 1248
Product Wiki & Tutorials Connect the 5 V Grove Line Finder v1.1 through a 3.3 V logic interface and test black/white detection before building a line-following robot. Grove Line Finder v1.1 with ESP32: Wiring and Black-Line Test → Important ESP32 voltage connection Seeed specifies a 5 V supply for Grove Line Finder v1.1. Use a…
Product Wiki & Tutorials Compare adjustable, Mini and Digital Grove PIR sensors, wire them for ESP32 3.3 V logic and read motion without an extra Arduino library. Grove PIR Sensors with ESP32: Wiring and Motion Test → Mini PIR setup notes Use a 3.3 V supply for the ESP32 example. A Grove connector alone does…
Battery Included: No High-concerned chemical: None Compatible With: arduino Accessory Type: Sensor Grove – NFC built around PN532 module Contactless communication at 13.56MHz. Support ISO14443 Type A and Type B protocols and I2C or UART communication protocols. Description Grove – NFC built around PN532 module Contactless communication at 13.56MHz. Support ISO14443 Type A and Type B protocols and I2C…
Features 🌱3.5mm pitch pin: The 3.5mm diameter hole is suitable for most connections between devices 🌱High current/voltage adaptable: Rate up to 125V @ 6A 🌱Grove unified socket: The product ensures “Plug and Play” and could be versatile for various applications of Grove Description Grove – Screw Terminal with four 3.5mm pitch pins rate up…
Features Easy to use: Plug the expansion board into the Arduino Nano or Seeeduino Nano and use it directly. Numerous interfaces: It expands to 8 Grove connectors, including 3 Grove digital connectors, 3 Grove analog connectors, 1 Grove I2C connector, and 1 Grove UART connector. Grove unified socket: The shield ensures “Plug and Play” and…
Product Wiki & Tutorials Select the PAJ7660 I2C switch mode, use the correct pag7660 driver and test finger counts, rotation and swipes with ESP32. PAJ7660 with ESP32: I2C Gesture Sensor Tutorial → Technical setup notes PAJ7660 Grove Smart IR Gesture Sensor. In the Seeed Grove_Gesture library, use the pag7660 class and pag7660_gesture_t result type. Rear…
Grove – Temp&Humi&Barometer Sensor (BME280) is a breakout board for Bosch BMP280, a high-precision, low-power combined humidity, pressure, and temperature sensor. Features 🌱High-performance environmental detection: With the help of BME280 module, it can simultaneously detect temperature and humidity, air pressure, to achieve a stronger detection effect. 🌱Robust measurement range: The sensor can operate normally from…
Product Wiki & Tutorials Grove connector and module power details differ from the generic breakout; use the matching wiring section. VL53L0X with ESP32: ToF Distance & Status Checks → Technical setup notes Grove VL53L0X time-of-flight distance sensor with I2C communication. Use the Grove board connector pinout, not a different generic breakout connector order. Default sensor…
The Grove-Relay module is a digital normally-open switch that can handle the current up to 5A at 250VAC for long periods of time. When the relay is switched on, the LED will light up and the relay will allow current to flow. The peak voltage capability is 250V at 10A. It is widely used in…
4.3” LCD-TFT HMI Without touch display module Supports WiFi and Bluetooth Support lithium battery power supply Without touch 480 x 272 screen resolution RGB 65K true-to-life colours IPS glass panel Onboard 240MHz LX6 MCU 520K Byte RAM 8 MB PSRAM 4 MB Flash memory JST1.25 4 Pins (+5V, TX, RX, GND) TTL serial interface
5.0” LCD-TFT Capacitive HMI touch display module Supports WiFi and Bluetooth Support lithium battery power supply Capacitive touch 800 x 480 screen resolution RGB 65K true-to-life colours IPS glass panel Onboard 240MHz LX6 MCU 520K Byte RAM 8 MB PSRAM 16 MB Flash memory JST1.25 4 Pins (+5V, TX, RX, GND) TTL serial interface
Typical applications: UV tester, UV watch, outdoor sports equipment, UV lamp monitoring, mobile phone, etc This product is particularly suitable for specifications in the field of mobile phones. And there is a linear current directly corresponding to the UV INDEX. 1. Small size: 11mm × 27mm 2. Low power consumption: The power supply voltage is…
Датчик температуры и давления воздуха GY BMP280 5V BME280 I2C SPI 1.8-5V GY-BMP280-3.3V для Arduino, модуль барометрических цифровых датчиков.
ADXL345 is a small and thin ultra-low power 3-axis accelerometer with high resolution (13 bits) and a measurement range of ± 16g. The digital output data is in 16 bit binary complement format, which can be accessed through SPI (3-wire or 4-wire) or IIC digital interface; ADXL345 is suitable for mobile device applications. It can…
Product Wiki & Tutorials Wire the GY-521, select its I2C address and read acceleration and angular velocity with a complete Arduino example. MPU6050 / GY-521 with ESP32: Motion & Gyro Readings → MPU-6050 is a sensor module that integrates a 3-axis gyroscope and 3-axis acceleration. The module uses an I2C interface for communication, calculates acceleration,…
Buy MLX90614 GY-906 Infrared Temperature Sensor Module. This contactless IR thermometer detects surface temperature without touch. Compatible with Arduino, ESP32 & Raspberry Pi.
Product Wiki & Tutorials Check IR-LED power, enable proximity-assisted gestures and recognize four directions using the GY-9960 module. APDS9960 with ESP32: I2C Gesture Recognition → The APDS series is an environmental brightness sensor that integrates ALS, infrared LED, and proximity detector optical modules, as well as ambient light sensing (ALS). It uses dual photodiodes to…
The GY-NEO6M V2 GPS Module is a high-performance GPS receiver designed for Arduino and flight control systems like APM2.5. It features the reliable NEO-6M GPS chip, built-in EEPROM for configuration storage, and an active high-gain antenna for improved signal reception. Operating on 3V–5V with RS232 TTL compatibility, it ensures broad hardware support. Key benefits include fast satellite acquisition, stable positioning, and easy integration into UAVs, drones, and robotics. Its compact design, low power consumption, and plug-and-play functionality make it ideal for precision navigation and real-time tracking applications.
Hackheld is a open source hackable handheld for DIY. It comes installed with the latest ESP8266 Deauther software. With this software, you can perform different attacks to test WiFi networks. Please note that the ESP8266 does only support 2.4GHz. You can also use it to develop your own software. It is simple to use, just…
1. Built-in 400 classic games: Arcade retro games, Logic & math, Sports, Puzzle, Arcade, Shooting, Action, Racing, Fighting games, Strategy, Adventure, Card games and more to meet your demand to play varieties of games what you like. 2. High-resolution screen：It features a colorful LCD screen and supports AV output, not only giving you a high-quality picture and gaming…
